www.vishay.com for technical questi ons, contact: tantalum@vishay.com document number: 40077 1 revision: 15-nov-05 t83 vishay sprague solid tantalum chip capacitors tantamount ? hi-rel cots, molded case features ? terminations: snpb, standard. 100 % tin available. ? molded case available in five case codes. ? compatible with "high volume" automatic pick and place equipment. ? high ripple current carrying capability. ? standard and low esr options. ? compliant terminations. performance/electrical characteristics operating temperature: - 55 c to + 85 c (to + 125 c with voltage derating) capacitance range: 0.1 f to 330 f capacitance tolerance: 20 %, 10 % standard voltage rating: 4 wvdc to 50 wvdc * pb containing terminations are not rohs compliant, exemptions may apply ordering information t83 d 107 k 010 e a a s ty p e c a s e code capacitance capacitance tolerance dc voltage rating at + 85 c termination and packaging reliability level surge current esr see ratings and case codes ta b l e . this is expressed in picofarads. the first two digits are the significant figures. the third is the number of zeros to follow. k = 10 % m = 20 % this is expressed in volts. to complete the three-digit block, zeros precede the voltage rating. a decimal point is indicated by an "r" (6r3 = 6.3 volts). e: sn/pb solder/7" (178 mm) reels f: sn/pb solder/13" (330 mm) reels c: 100% tin/7" (178 mm) reels d: 100% tin/13" (330 mm) reels a = 1.0 % b = 0.1 % c = 0.01 % s = hi-rel standard z = non-er a = 10 cycles at + 25 c b = 10 cycles at - 55 c/+ 85 c s = 3 cycles at + 25 c z = none s = std l = low dimensions in inches [millimeters] case code eia size l w h p t w t h (min.) a 3216-18 0.126 0.008 [3.2 0.20] 0.063 0.008 [1.6 0.20] 0.063 0.008 [1.6 0.20] 0.031 0.012 [0.80 0.30] 0.047 0.004 [1.2 0.10] 0.028 [0.70] b 3528-21 0.138 0.008 [3.5 0.20] 0.110 0.008 [2.8 0.20] 0.075 0.008 [1.9 0.20] 0.031 0.012 [0.80 0.30] 0.087 0.004 [2.2 0.10] 0.028 [0.70] c 6032-28 0.236 0.012 [6.0 0.30] 0.126 0.012 [3.2 0.30] 0.098 0.012 [2.5 0.30] 0.051 0.012 [1.3 0.30] 0.087 0.004 [2.2 0.10] 0.039 [1.0] d 7343-31 0.287 0.012 [7.3 0.30] 0.170 0.012 [4.3 0.30] 0.110 0.012 [2.8 0.30] 0.051 0.012 [1.3 0.30] 0.095 0.004 [2.4 0.10] 0.039 [1.0] e 7343-43 0.287 0.012 [7.3 0.30] 0.170 0.012 [4.3 0.30 0.158 0.012 [4.0 0.30] 0.051 0.012 [1.3 0.30] 0.095 0.004 [2.4 0.10] 0.039 [1.0] a v aila b le p b -free rohs * compliant l t min. h h w t w p
document number: 40077 for technical questions, contact: tantalum@vishay.com www.vishay.com revision: 15-nov-05 2 t83 solid tantalum chip capacitors tantamount ? hi-rel cots, molded case vishay sprague ratings and case codes f 4 v 6.3 v 10 v 16 v 20 v 25 v 35 v 50 v 0.10 aa 0.15 aa/b 0.22 ab 0.33 aab 0.47 aabb/c 0.68 a a b b c 1.0 aaabbc 1.5 a aabbb/cc/d 2.2 a a b b c c d 3.3 aabbbb/ccd 4.7 a a/b a/b b b/c c c/d d 6.8 bbbccc/dd 10 b b c c c c/d d 15 b c c d d 22 c ddde 33 c d d d e 47 d d d e 68 dddde 100 d d d e 150 d d/e 220 e e 330 e e construction and marking cathode termination (-) tantalum capacitor element polarity stripe (+) epoxy case anode weld positive termination capacitance pf code indicates hi-rel polarity band volta g e code v 104t a case date code vishay spra g ue lo g o indicates hi-rel volta g e capacitance f polarity band 22 t10 xx 2 b, c, d, e cases marking: capacitor marking includes anode (+) polarity band, capacitance in microfarads and the voltage rating of + 85 c. 'a' case capacitors use a letter code for the voltage and eia capacitance code. the sprague ? trademark will be included if space permits. capacitors rated at 6.3 v shall be marked 6 v. a manufacturing date code is marked on all capacitors. call the factory for further explanation. volts code 4.0 6.3 10 16 20 25 35 50 t v e d c a j g marking construction
t83 vishay sprague solid tantalum chip capacitors tantamount ? hi-rel cots, molded case www.vishay.com for technical questi ons, contact: tantalum@vishay.com document number: 40077 3 revision: 15-nov-05 standard/extended ratings capacitance (f) case code part number max. dc leakage at + 25 c (a) max. df at + 25 c 120 hz (%) std. (s) max. esr at + 25 c 100 khz (ohms) low (l) max. esr at + 25 c 100 khz (ohms) 4 wvdc at + 85 c, surge = 5.2 v . . . .2.7 wvdc at + 125 c, surge = 3.4 v 2.2 a t83a225(1)004(2)(3)(4)(5) 0.5 6 7.600 6.000 3.3 a t83a335(1)004(2)(3)(4)(5) 0.5 6 7.600 4.000 4.7 a t83a475(1)004(2)(3)(4)(5) 0.5 6 6.300 3.500 6.8 b t83b685(1)004(2)(3)(4)(5) 0.5 6 4.500 2.000 10 b t83b106(1)004(2)(3)(4)(5) 0.5 6 3.500 1.200 15 b t83b156(1)004(2)(3)(4)(5) 0.6 6 2.900 1.200 33 c t83c336(1)004(2)(3)(4)(5) 1.3 6 1.800 0.500 68 d t83d686(1)004(2)(3)(4)(5) 2.7 6 0.800 0.175 100 d t83d107(1)004(2)(3)(4)(5) 4.0 6 0.700 0.175 150 d t83d157(1)004(2)(3)(4)(5) 6.0 8 0.600 0.150 330 e t83e337(1)004(2)(3)(4)(5) 13.2 8 0.500 0.100 6.3 wvdc at + 85 c, surge = 8 v . . . 4 wvdc at 125 c, surge = 5 v 1.5 a t83a155(1)6r3(2)(3)(4)(5) 0.5 6 8.000 6.000 2.2 a t83a225(1)6r3(2)(3)(4)(5) 0.5 6 7.600 6.000 3.3 a t83a335(1)6r3(2)(3)(4)(5) 0.5 6 6.300 5.000 4.7 a t83a475(1)6r3(2)(3)(4)(5) 0.5 6 5.500 3.500 4.7 b t83b475(1)6r3(2)(3)(4)(5) 0.5 6 3.400 1.800 6.8 b t83b685(1)6r3(2)(3)(4)(5) 0.5 6 3.400 1.200 10 b t83b106(1)6r3(2)(3)(4)(5) 0.6 6 2.900 1.000 15 c t83c156(1)6r3(2)(3)(4)(5) 0.9 6 1.800 0.600 22 c t83c226(1)6r3(2)(3)(4)(5) 1.3 6 1.800 0.500 47 d t83d476(1)6r3(2)(3)(4)(5) 2.8 6 0.800 0.200 68 d t83d686(1)6r3(2)(3)(4)(5) 4.1 6 0.700 0.200 100 d t83d107(1)6r3(2)(3)(4)(5) 6.0 6 0.700 0.140 150 d t83d157(1)6r3(2)(3)(4)(5) 9.0 8 0.600 0.125 150 e t83e157(1)6r3(2)(3)(4)(5) 9.0 8 0.500 0.100 220 e t83e227(1)6r3(2)(3)(4)(5) 13.2 8 0.500 0.100 330 e t83e337(1)6r3(2)(3)(4)(5) 19.8 8 0.500 0.100 10 wvdc at + 85 c, surge = 8 v . . . 4 wvdc at 125 c, surge = 5 v 1 a t83a105(1)010(2)(3)(4)(5) 0.5 4 9.300 6.000 1.5 a t83a155(1)010(2)(3)(4)(5) 0.5 6 8.000 6.000 3.3 b t83b335(1)010(2)(3)(4)(5) 0.5 6 3.500 2.500 4.7 a t83a475(1)010(2)(3)(4)(5) 0.5 6 5.000 3.000 4.7 b t83b475(1)010(2)(3)(4)(5) 0.5 6 3.400 1.500 6.8 b t83b685(1)010(2)(3)(4)(5) 0.7 6 2.900 1.200 10 c t83c106(1)010(2)(3)(4)(5) 1.0 6 1.800 0.550 15 c t83c156(1)010(2)(3)(4)(5) 1.5 6 1.800 0.500 33 d t83d336(1)010(2)(3)(4)(5) 3.3 6 0.800 0.250 47 d t83d476(1)010(2)(3)(4)(5) 4.7 6 0.700 0.200 68 d t83d686(1)010(2)(3)(4)(5) 6.8 6 0.700 0.150 100 d t83d107(1)010(2)(3)(4)(5) 10.0 8 0.600 0.100 220 e t83e227(1)010(2)(3)(4)(5) 22.0 8 0.500 0.100 (1) capacitance tolerance: k, m (2) termination and packaging: c, d, e, f (3) reliability level: a, b, c, s, z (4) surge current: a, b, s, z (5) esr: l, s
document number: 40077 for technical questions, contact: tantalum@vishay.com www.vishay.com revision: 15-nov-05 4 t83 solid tantalum chip capacitors tantamount ? hi-rel cots, molded case vishay sprague standard/extended ratings capacitance (f) case code part number max. dc leakage at + 25 c (a) max. df at + 25 c 120 hz (%) std. (s) max. esr at + 25 c 100 khz (ohms) low (l) max. esr at + 25 c 100 khz (ohms) 16 wvdc at + 85 c, surge = 20 v . . .10 wvdc at + 125 c, surge = 12 v 0.68 a t83a684(1)016(2)(3)(4)(5) 0.5 4 11.000 8.000 1 a t83a105(1)016(2)(3)(4)(5) 0.5 4 9.300 6.000 1.5 a t83a55(1)016a(2)(3)(4)(5) 0.5 6 6.700 6.000 2.2 b t83b225(1)016(2)(3)(4)(5) 0.5 6 4.600 2.500 3.3 b t83b335(1)016(2)(3)(4)(5) 0.5 6 3.500 2.000 4.7 b t83b475(1)016(2)(3)(4)(5) 0.8 6 2.900 1.500 6.8 c t83c685(1)016(2)(3)(4)(5) 1.1 6 1.900 0.600 10 c t83c106(1)016(2)(3)(4)(5) 1.6 6 1.800 0.450 22 d t83d226(1)016(2)(3)(4)(5) 3.5 6 0.800 0.250 33 d t83d336(1)016(2)(3)(4)(5) 5.3 6 0.700 0.225 47 d t83d476(1)016(2)(3)(4)(5) 7.5 6 0.700 0.150 68 d t83d686(1)016(2)(3)(4)(5) 10.9 6 0.600 0.150 100 e t83e107(1)016(2)(3)(4)(5) 16.0 8 0.600 0.100 20 wvdc at + 85 c, surge = 26 v . . . 13 wvdc at + 125 c, surge = 16 v 0.47 a t83a474(1)020(2)(3)(4)(5) 0.5 4 12.000 9.000 0.68 a t83a684(1)020(2)(3)(4)(5) 0.5 4 10.000 8.000 1 a t83a105(1)020(2)(3)(4)(5) 0.5 4 8.400 5.500 1.5 b t83b155(1)020(2)(3)(4)(5) 0.5 6 4.600 2.500 2.2 b t83b225(1)020(2)(3)(4)(5) 0.5 6 3.500 1.500 3.3 b t83b335(1)020(2)(3)(4)(5) 0.7 6 3.000 1.300 4.7 b t83b475(1)020(2)(3)(4)(5) 0.9 6 2.900 1.000 4.7 c t83c475(1)020(2)(3)(4)(5) 0.9 6 2.300 0.600 6.8 c t83c685(1)020(2)(3)(4)(5) 1.4 6 1.900 0.550 10 c t83c106(1)020(2)(3)(4)(5) 2.0 6 1.700 0.450 15 d t83d156(1)020(2)(3)(4)(5) 3.0 6 0.900 0.300 22 d t83d226(1)020(2)(3)(4)(5) 4.4 6 0.700 0.225 33 d t83d336(1)020(2)(3)(4)(5) 6.6 6 0.700 0.200 47 e t83e476(1)020(2)(3)(4)(5) 9.4 6 0.600 0.150 68 e t83e686(1)020(2)(3)(4)(5) 13.6 6 0.600 0.150 25 wvdc at + 85 c, surge = 32 v . . . 17 wvdc at + 125 c, surge = 20 v 0.33 a t83a334(1)025(2)(3)(4)(5) 0.5 4 14.000 10.000 0.47 a t83a474(1)025(2)(3)(4)(5) 0.5 4 12.000 9.000 0.68 b t83b684(1)025(2)(3)(4)(5) 0.5 4 7.000 5.000 1 b t83b105(1)025(2)(3)(4)(5) 0.5 4 5.000 2.000 1.5 b t83b155(1)025(2)(3)(4)(5) 0.5 6 4.600 2.000 2.2 c t83c225(1)025(2)(3)(4)(5) 0.6 6 2.900 1.000 3.3 b t83b335(1)025(2)(3)(4)(5) 0.8 6 3.100 1.500 3.3 c t83c335(1)025(2)(3)(4)(5) 0.8 6 2.300 1.000 4.7 c t83c475(1)025(2)(3)(4)(5) 1.2 6 2.000 0.525 6.8 c t83c685(1)025(2)(3)(4)(5) 1.7 6 1.700 0.500 6.8 d t83d685(1)025(2)(3)(4)(5) 1.7 6 1.200 0.350 10 c t83c106(1)025(2)(3)(4)(5) 2.5 6 1.500 0.450 (1) capacitance tolerance: k, m (2) termination and packaging: c, d, e, f (3) reliability level: a, b, c, s, z (4) surge current: a, b, s, z (5) esr: l, s
t83 vishay sprague solid tantalum chip capacitors tantamount ? hi-rel cots, molded case www.vishay.com for technical questi ons, contact: tantalum@vishay.com document number: 40077 5 revision: 15-nov-05 standard/extended ratings capacitance (f) case code part number max. dc leakage at + 25 c (a) max. df at + 25 c 120 hz (%) std. (s) max. esr at + 25 c 100 khz (ohms) low (l) max. esr at + 25 c 100 khz (ohms) 25 wvdc at + 85 c, surge = 32 v . . . 17 wvdc at + 125 c, surge = 20 v 10 d t83d106(1)025(2)(3)(4)(5) 2.5 6 1.000 0.300 15 d t83d156(1)025(2)(3)(4)(5) 3.8 6 0.800 0.250 22 d t83d226(1)025(2)(3)(4)(5) 5.5 6 0.700 0.200 33 e t83e336(1)025(2)(3)(4)(5) 8.3 6 0.600 0.200 35 wvdc at + 85 c, surge = 46 v . . . 23 wvdc at + 125 c, surge = 28 v 0.10 a t83a104(1)035(2)(3)(4)(5) 0.5 4 20.000 10.000 0.15 a t83a154(1)035(2)(3)(4)(5) 0.5 4 18.000 6.000 0.22 a t83a224(1)035(2)(3)(4)(5) 0.5 4 15.000 6.000 0.33 a t83a334(1)035(2)(3)(4)(5) 0.5 4 13.000 6.000 0.47 b t83b474(1)035(2)(3)(4)(5) 0.5 4 8.000 2.500 0.68 b t83b684(1)035(2)(3)(4)(5) 0.5 4 6.500 2.500 1 b t83b105(1)035(2)(3)(4)(5) 0.5 4 5.000 2.000 1.5 b t83b155(1)035(2)(3)(4)(5) 0.5 6 4.200 2.000 1.5 c t83c155(1)035(2)(3)(4)(5) 0.5 6 3.800 0.900 2.2 c t83c225(1)035(2)(3)(4)(5) 0.8 6 2.900 0.900 3.3 c t83c335(1)035(2)(3)(4)(5) 1.2 6 2.100 0.700 4.7 c t83c475(1)035(2)(3)(4)(5) 1.6 6 1.900 0.500 4.7 d t83d475(1)035(2)(3)(4)(5) 1.6 6 1.300 0.450 6.8 d t83d685(1)035(2)(3)(4)(5) 2.4 6 1.100 0.300 10 d t83d106(1)035(2)(3)(4)(5) 3.5 6 0.800 0.300 22 e t83e226(1)035(2)(3)(4)(5) 7.7 6 0.600 0.275 50 wvdc at + 85 c, surge = 65 v . . . 33 wvdc at + 125 c, surge = 40 v 0.10 a t83a104(1)050(2)(3)(4)(5) 0.5 4 19.000 10.000 0.15 a t83a154(1)050(2)(3)(4)(5) 0.5 4 17.000 10.000 0.15 b t83b154(1)050(2)(3)(4)(5) 0.5 4 14.000 9.000 0.22 b t83b224(1)050(2)(3)(4)(5) 0.5 4 12.000 8.500 0.33 b t83b334(1)050(2)(3)(4)(5) 0.5 4 10.000 4.500 0.47 b t83b474(1)050(2)(3)(4)(5) 0.5 4 8.400 4.000 0.47 c t83c474(1)050(2)(3)(4)(5) 0.5 4 6.700 1.800 0.68 c t83c684(1)050(2)(3)(4)(5) 0.5 4 5.900 1.600 1 c t83c105(1)050(2)(3)(4)(5) 0.5 4 4.600 1.600 1.5 c t83c155(1)050(2)(3)(4)(5) 0.8 6 3.400 1.500 1.5 d t83d155(1)050(2)(3)(4)(5) 0.8 6 2.900 1.000 2.2 d t83d225(1)050(2)(3)(4)(5) 1.1 6 2.100 0.800 3.3 d t83d335(1)050(2)(3)(4)(5) 1.7 6 1.700 0.800 4.7 d t83d475(1)050(2)(3)(4)(5) 2.4 6 1.200 0.600 (1) capacitance tolerance: k, m (2) termination and packaging: c, d, e, f (3) reliability level: a, b, c, s, z (4) surge current: a, b, s, z (5) esr: l, s
document number: 40077 for technical questions, contact: tantalum@vishay.com www.vishay.com revision: 15-nov-05 6 t83 solid tantalum ch ip capacitors tantamount ? hi-rel cots, molded case vishay sprague guide to application 1. recommended voltage derating guidelines: standard conditions, for example; output filters severe conditions, for example; input filters 2. a-c ripple current: the maximum allowable ripple current shall be determined from the formula: where, p = power dissipation in watts at + 25 c as given in the table in paragraph number 6 (power dissipation) r esr = the capacitor equivalent series resistance at the specified frequency. 3. a-c ripple voltage: the maximum allowable ripple voltage shall be determined from the formula: or, from the formula: where, p = power dissipation in watts at + 25 c as given in the table in paragraph number 6 (power dissipation). r esr = the capacitor equivalent series resistance at the specified frequency. z = the capacitor impedance at the specified frequency. 3.1 the sum of the peak ac voltage plus the applied dc voltage shall not exceed the dc voltage rating of the capacitor. 3.2 the sum of the negative peak ac voltage plus the applied dc voltage shall not allow a voltage reversal exceeding 10 % of the dc working voltage at + 25 c. 4. reverse voltage: these capacitors are capable of withstanding peak voltages in the reverse direction equal to 10 % of the dc rating at + 25 c, 5 % of the dc rating at + 85 c and 1 % of the dc rating at + 125 c. 5. temperature derating: if these capacitors are to be operated at temperatures above + 25 c, the permissible rms ripple current or voltage shall be calculated using the derating factors as shown: 6. power dissipation: power dissipation will be affected by the heat sinki ng capability of the mounting surface. non-sinusoidal ripple current may produce heating effects which differ from those shown. it is important that the equivalent i rms value be established when calculating permissible operating levels. (power dissipation calculated using + 25 c temperature rise.) 7. printed circuit board materials: type t83 capacitors are compatible with commonly used printed circuit board materials (alumina substrates, fr4, fr5, g10, ptfe-fl uorocarbon and porcelanized steel). 8. attachment: 8.1 solder paste: the recommended thickness of the solder paste after application is 0.007" 0.001" [0.178 mm 0.025 mm]. care should be exercised in selecting the solder paste. the metal purity should be as high as practical. the fl ux (in the paste) must be active enough to remove the oxides formed on the metallization prior to the exposure to soldering heat. in practice this can be aided by extending the solder preheat time at temperatures below the liquidous state of the solder. capacitor voltage rating (v) operating voltage (v) 4.0 2.5 6.3 3.6 10 6.0 16 10 20 12 25 15 35 24 50 28 capacitor voltage rating (v) operating voltage (v) 4.0 2.5 6.3 3.3 10 5.0 16 8.0 20 10 25 12 35 15 50 24 i rms p r esr --------------- - = v rms z p r esr --------------- - = v rms i rms z = temperature derating factor + 25 c 1.0 + 85 c 0.9 + 125 c 0.4 case code maximum permissible power dissipation at + 25 c (watts) in free air a 0.075 b 0.085 c 0.110 d 0.150 e 0.165
t83 vishay sprague solid tantalum chip capacitors tantamount ? hi-rel cots, molded case www.vishay.com for technical questi ons, contact: tantalum@vishay.com document number: 40077 7 revision: 15-nov-05 guide to application (continued) 8.2. soldering: capacitors can be attached by conventional soldering techniques; vapor phase, convection reflow, infrared reflow, wave soldering and hot plate methods. the soldering profile charts show recommended time/temperature conditions for soldering. preheating is recommended. the recommended maximum ramp rate is 2 c per second. attachment with a soldering iron is not recommended due to the difficulty of controlling temperature and time at te mperature. the soldering iron must never come in contact with the capacitor. 8.2.1. backward and forward compatibility: capacitors with snpb or 100 % tin termination finishes can be soldered using snpb or lead (pb)-free soldering processes. 9. cleaning (flux removal) after soldering: the t83 is compatible with all commonly used solvents such as tes, tms, prelete, chlorethane, terpene and aqueous cleaning media. however, cfc/ods products are not used in the production of these devices and are not recommended. solvents containing methylene chloride or other epoxy solvents should be avoided since these will attack the epoxy encapsulation material. 9.1 when using ultrasonic cleaning, the board may resonate if the output power is too high. this vibration can cause cracking or a decrease in the adherence of the termination. do not exceed 9w/l at 40 khz for 2 minutes. 10. leakage current: capacitors shall be stabilized at the rated temperature for 30 minutes. rated voltage shall be applied to capacitors for 5 minutes using a steady source of power (such as a regulated power supply) with 1000 ohm resistor connected in series with the capacitor under te st to limit the charging current. leakage current shall then be measured. note that the leakage curre nt varies with temperature and applied voltage. see graph opposite for the appropriate adjustment factor. soldering profile typical leakage current factor range temperature (c) time (seconds) recommended snpb reflow soldering profile 240 c 10 sec 183 c 150 c 100 c 60 - 90 sec preheat 60 sec all case codes 25 c temperature (c) time (seconds) recommended pb free reflow soldering profile 260 c 10 sec 217 c 200 c 150 c 60 - 150 sec preheat 60 sec all case codes 25 c leakage current factor percent of rated voltage 100 10 1.0 0.1 0.01 0.001 0 10 20 30 40 50 60 70 80 90 100 + 125 ?c + 85 ?c + 55 ?c + 25 ?c 0 ?c - 55 ?c
document number: 40077 for technical questions, contact: tantalum@vishay.com www.vishay.com revision: 15-nov-05 8 t83 solid tantalum chip capacitors tantamount ? hi-rel cots, molded case vishay sprague 10.1 at + 25 c , the leakage current shall not exceed the value listed in the standard ratings table. 10.2 at + 85 c, the leakage current shall not exceed 10 times the value listed in the standard ratings table. 10.3 at + 125 c, the leakage current shall not exceed 12 times the value listed in the standard ratings table. 11. recommended mounting pad geometries: proper mounting pad geometries are essential for successful solder connections. these dimensions are highly process sensitive and should be designed to minimize component rework due to unacceptable solder joints. the dimensional configurations shown are the recommended pad geometries for both wave and reflow soldering techniques. these dimensions are intended to be a starting point for circuit board designers and may be fine tuned if necessary based upon the peculiarities of t he soldering process and/or circuit board design. recommended mounting pad geometries in inches [millimeters] pad dimensions pad dimensions case code a (min.) b (nom.) c (nom.) d (nom.) e (nom.) case code a (min.) b (nom.) c (nom.) d (nom.) e (nom.) a 0.034 [0.87] 0.085 [2.15] 0.053 [1.35] 0.222 [5.65] 0.048 [1.23] a 0.071 [1.80] 0.085 [2.15] 0.053 [1.35] 0.222 [5.65] 0.048 [1.23] b 0.061 [1.54] 0.085 [2.15] 0.065 [1.65] 0.234 [5.95] 0.048 [1.23] b 0.110 [2.80] 0.085 [2.15] 0.065 [1.65] 0.234 [5.95] 0.048 [1.23] c 0.061 [1.54] 0.106 [2.70] 0.124 [3.15] 0.337 [8.55] 0.050 [1.28] c 0.110 [2.80] 0.106 [2.70] 0.124 [3.15] 0.337 [8.55] 0.050 [1.28] d 0.066 [1.68] 0.106 [2.70] 0.175 [4.45] 0.388 [9.85] 0.050 [1.28] d 0.118 [3.00] 0.106 [2.70] 0.175 [4.45] 0.388 [9.85] 0.050 [1.28] e 0.066 [1.68] 0.106 [2.70] 0.175 [4.45] 0.388 [9.85] 0.050 [1.28] e 0.118 [3.00] 0.106 [2.70] 0.175 [4.45] 0.388 [9.85] 0.050 [1.28] wave solder pads d bc e a reflow solder pads a b c d e
t83 vishay sprague solid tantalum chip capacitors tantamount ? hi-rel cots, molded case www.vishay.com for technical questi ons, contact: tantalum@vishay.com document number: 40077 9 revision: 15-nov-05 tape and reel packaging in inches [millimeters] tape size b 1 (max.) d 1 (min.) f k (max.) p w a 0 b 0 k 0 8 mm 0.165 [4.2] 0.039 [1.0] 0.138 0.002 [3.5 0.05] 0.094 [2.4] 0.157 0.004 [4.0 1.0] 0.315 0.012 [8.0 0.30] notes: a 0 b 0 k 0 are determined by component size. the clearance between the component and the cavity must be within 0.002" [0.05 mm] minimum to 0.020" [0.50 mm] maximum for 8 mm tape and 0.002" [0.05 mm] minimum to 0.026" [0.65 mm] maximum for 12 mm tape. 12 mm 0.323 [8.2] 0.059 [1.5] 0.217 0.002 [5.5 0.05] 0.177 [4.5] 0.315 0.004 [8.0 1.0] 0.472 0.012 [12.0 0.30] tape and reel specifications: all case codes are available on plastic embossed tape per eia-481- 1. tape reeling per iec 286-3 is also available. standard reel diameter is 13" [330 mm]. 7" [178 mm] reels are available. the most efficient packaging quantities are full reel increments on a given reel diameter. the quantities shown allow for the sealed empty pockets required to be in conformance with eia-481-1. reel size must be specified in the vishay sprague part number. case code tape width component pitch units per reel 7" [178 mm] reel 13" [330 mm] reel a 8 mm 4 mm 2000 9000 b 8 mm 4 mm 2000 8000 c 12 mm 8 mm 500 3000 d 12 mm 8 mm 500 2500 e 12 mm 8 mm 400 1500 k max. b max. 1 0.024 [0.600] max. k 0 top cover tape 0.059 + 0.004 - 0.0 [1.5 + 0.10 - 0.0] 0.157 0.004 [4.0 0.10] 0.079 0.002 [2.0 0.050] 0.069 0.004 [1.75 0.10] w f d min. 1 direction of feed p b a 0 0 top cover tape thickness carrier embossment standard orientation is with the cathode (-) nearest to the sprocket holes per eia-481-1 and iec 286-3. direction of feed cathode (-) anode (+)
legal disclaimer notice vishay document number: 91000 www.vishay.com revision: 08-apr-05 1 notice specifications of the products displayed herein are subjec t to change without notice. vishay intertechnology, inc., or anyone on its behalf, assume s no responsibility or liability fo r any errors or inaccuracies. information contained herein is intended to provide a product description only. no license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document. except as provided in vishay's terms and conditions of sale for such products, vishay assumes no liability whatsoever, and disclaims any express or implied warranty, relating to sale and /or use of vishay products including liab ility or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyrigh t, or other intellectual property right. the products shown herein are not designed for use in medical, life-saving, or life-sustaining applications. customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify vishay for any damages resulting from such improper use or sale.
|
